ACOPIAN电源12EB120介绍及技术参数

ACOPIAN成立于1957年，主要做交流电源，直流电源，高压电源。

ACOPIAN电源12EB120技术参数

Input Voltage Range:	105 to 125
Nominal Output Voltage:	12
Output Current Amps:	1.2
Case Size:	EB-20

ACOPIAN电源产品特点

Although small in size, these mini-modules offer high performance at modest prices. All models, with series regulated outputs ranging from 1 to 75 volts and as high as 2.5 amps, may be mounted in an area only 3.5˝ x 2.5˝. Dual output models are available with the ratings commonly required for driving op amps and other balanced loads. Terminal strip input/output connections eliminate all need for sockets or soldering. Short circuit protection, encapsulated construction, and conservative design assure long term reliability

STANDARD FEATURES

• May be used in series

• No derating or heat sinking required

• Short circuit protected

• Small, lightweight

SPECIFICATIONS

Input Voltage: 105-125 VAC, 47 to 420 Hz, single phase.

Output Voltage Setting: Outputs are factory preset to within ±2% (1 to 9 volt models) or ±1% (10 to 75 volt models) of the nominal output voltage.

T/C terminal: For single output models, the T/C terminal can be used to trim the output more precisely to the nominal voltage rating by connecting an external resistor from the T/C terminal to either the + or– terminal. For dual output models, the T/C terminal is the output common.

Polarity: Either positive or negative terminal of a single output module may be grounded. Dual output modules have a positive/common/negative output terminal configuration.

Ambient Operating Temperature: –20 to +71°C. No derating required.

Storage Temperature: –55 to +85°C.

Temperature Coefficient: From 9 to 75 volts, typically 0.015%/°C; 1 to 8 volts, 0.03%/°C.

Impedance: 0.07 ohms at 1 kHz and 0.2 ohms at 10 kHz (approx.).

Mounting: Threaded mounting holes permit mounting toa chassis, cabinet wall or bracket, or they may be used on a test bench or tabletop. When wall-mounting or DIN rail mounting is desired, use accessory Mounting Kits on page H4.

虽然尺寸小，但这些迷你模块以适中的价格提供高性能。所有型号的串联稳压输出范围从 1 到75伏，最高可达2.5安，可以安装在仅3.5˝ x 2.5˝的区域内。双输出型号可提供驱动运算放大器和其他平衡负载通常所需的额定值。端子排输入/输出连接无需插座或焊接。短路保护、封装结构和保守设计确保长期可靠性

标准功能

• 可串联使用

• 无需降额或散热

• 短路保护

• 体积小、重量轻

规格

输入电压：105-125 VAC，47 至 420 Hz，单相。

输出电压设置：输出出厂预设为标称输出电压的 ±2%（1 至 9 伏型号）或 ±1%（10 至 75 伏型号）。

T/C 端子：对于单输出型号，通过将外部电阻器从 T/C 端子连接到 + 或 – 端子，T/C 端子可用于将输出更精确地调整到额定电压额定值。对于双输出型号，T/C 端子是输出公共端。

极性：单个输出模块的正极或负极都可以接地。双输出模块具有正/公共/负输出端子配置。

环境工作温度：–20 至 +71°C。无需降容。